D5030D

D5030D

SIL 3 Switch/Proximity Detector Repeater, Relay Output

شرکت GMI که سابقه ای طولانی در تولید بریر و رله های ایمنی دارد، اخیرا مدل های جدیدی را معرفی نموده است که دارای مشخصاتی فراتر از یک رله ایمنی معمولی هستند. این مدل ها دارای قابلیت های کم نظیر و کارامدی جهت استفاده در سیستم های با ضریب اطمینان بالا مانند ESD و F&G می باشند که از جمله می توان به موارد ذیل اشاره نمود:

  •    تشخیص انواع خطاها از بوبین رله تا سطح فیلد مطابق شکل زیر و اعلام نوع خطا از طریق مدباس و خروجی دیجیتال
    •    سازگار با پالس تست DCS/PLC
    •    قابلیت اندازه گیری مقاومت سلونوئید حتی با وجود دیودهای سری شده
    •    اندازه گیری ولتاژ موثر(قبل و بعد از وصل بار) و جریان بار
    •    تشخیص نشتی زمین
    •    قابلیت تعیین set point جهت ولتاژ تغذیه، مقاومت، جریان بار و نشتی زمین

 

توضیحات

Description

The dual channel Switch/Proximity Detector Repeater, D5030D module, is a unit suitable for applications requiring SIL 3 level (according to IEC 61508:2010 Ed. 2) in safety related systems for high risk industries. The unit can be configured for switch or proximity detector (EN60947-5-6, NAMUR), NO or NC and for NE or ND SPST relay output contact. Each channel enables a Safe Area load to be controlled by a switch, or a proximity detector, located in Hazardous Area. Fault detection circuit (DIP switch configurable) is available for both proximity sensor and switch equipped with end of line resistors. In case of fault, when enabled it de-energizes the corresponding output relay and turns the fault LED on; when disabled the corresponding output relay repeats the input line open or closed status as configured.
D5030D is programmable via dip switches as single input and two independent outputs. Out 2 can be programmed for output duplicating Out 1 or Fault detection Out.
In case of duplication, relay actuation can be independently configured for each output. In case of fault output, relay actuation can be programmed as normally energized or normally de-energized.
Mounting on standard DIN-Rail, with or without Power Bus, in Safe Area / Non Hazardous Location or in Zone 2 / Class I, Division 2 or Class I, Zone 2.

Features

  • Systematic capability SIL 3
    • 2 fully independent channels.
    • Input from Zone 0 (Zone 20), installation in Zone 2.
    • NO/NC switch/proximity Detector Input,NE/ND relay actuation mode.
    • Field open and short circuit detection.
    • Three port isolation, Input/Output/Supply.
    • EMC Compatibility to EN61000-6-2, EN61000-6-4,EN61326-1, EN61326-3-1 for safety system.
    • In-field programmability by DIP Switch.
    • High Density, two channels per unit.
    • Simplified installation using standard DIN-Rail and plug-in terminal blocks, with or without Power Bus.
    • 250 Vrms (Um) max. voltage allowed to the instruments associated with the barrier.

Supply

18-30 Vdc

Channels

2 (1 Channel: D5030S)

SIL level

SIL 3

Series

D5000

 

Supply

24 Vdc nom (18 to 30 Vdc), reverse polarity protected.

Current consumption: 35 mA (D5030D), 18 mA (D5030S), @ 24 Vdc with

short circuit input and relay energized, typical.

Power dissipation: 0.85 W (D5030D), 0.45 W (D5030S), @ 24 Vdc with

short circuit input and relay energized, typical.

Input

Input switching current levels: ON ≥ 2.1 mA, OFF ≤ 1.2 mA.

Fault current levels: open fault ≤ 0.2 mA, short fault ≥ 6.8 mA.

Input equivalent source: 8 V 1 kΩ typical (8 V no load, 8 mA short).

Output

Voltage free SPST (D5030D) or SPDT (D5030S) relay contact.

Contact material: Ag Alloy (Cd free), gold plated.

Contact rating: 4 A 250 Vac 1000 VA, 4 A 250 Vdc 120 W (resistive load).

Contact min. switching current: 1 mA.

DC and AC load breaking capacity: refer to Instruction Manual.

Mechanical / electrical life: 5 * 10⁶ / 3 * 10⁴ operation, typical.

Operate / release time: 8 / 4 ms, typical.

Frequency response: 10 Hz maximum.

Isolation

I.S. In/Out 2.5 kV; I.S. In/Supply 2.5 kV; I.S. In/ I.S In 500 V; Out/Supply 2.5

kV; Out/Out 2.5 kV.

Environmental conditions

Operating temperature: temperature limits –40 to +70 °C.

Storage temperature: temperature limits –45 to +80 °C.

Safety description

Associated apparatus and non-sparking electrical equipment.

Uo = 10.5 V, Io = 22 mA, Po = 56 mW at terminals 7-8, 9-10.

Um = 250 Vrms or Vdc, -40 °C ≤ Ta ≤ 70 °C.

Mounting

DIN-Rail 35 mm, with or without Power Bus.

Weight: about 140 g (D5030D), 120 g (D5030S).

Connection: by polarized plug-in disconnect screw terminal blocks to

accommodate terminations up to 2.5 mm² (13 AWG).

Dimensions: Width 12.5 mm, Depth 123 mm, Height 120 mm.

نقد و بررسی‌ها

هیچ دیدگاهی برای این محصول نوشته نشده است.

اولین کسی باشید که دیدگاهی می نویسد “D5030D”

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

فهرست